View MC10H136_30594.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Universal Hexadecimal Counter
The MC10H136 is a high speed synchronous hexadecimal counter. This 10H part is a functional/pinout duplication of the standard MECL 10K family part, with 100% improvement in counting frequency and no increase in power-supply current. * Counting Frequency, 250 MHz Minimum * Voltage Compensated * Power Dissipation, 625 mW Typical * MECL 10K-Compatible * Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range)
MC10H136
L SUFFIX CERAMIC PACKAGE CASE 620-10 P SUFFIX PLASTIC PACKAGE CASE 648-08 FN SUFFIX PLCC CASE 775-02
MAXIMUM RATINGS
Characteristic Power Supply (VCC = 0) Input Voltage (VCC = 0) Output Current -- Continuous -- Surge Operating Temperature Range Storage Temperature Range -- Plastic -- Ceramic Symbol VEE VI Iout TA Tstg Rating -8.0 to 0 0 to VEE 50 100 0 to +75 -55 to +150 -55 to +165 Unit Vdc Vdc mA C C C
FUNCTION SELECT TABLE
CIN X L H L H X
S1 L L L H H H
S2 L H H L L H
INPUTS
Operating Mode Preset (Program) Increment (Count Up) Hold Count Decrement (Count Down) Hold Count Hold (Stop Count)
OUTPUTS
ELECTRICAL CHARACTERISTICS (VEE = -5.2 V 5%) (See Note)
0 Characteristic Power Supply Current Input Current High Pins 5, 6, 11, 12, 13 Pin 9 Pin 7 Pin 10 Input Current Low High Output Voltage Low Output Voltage High Input Voltage Low Input Voltage Symbol IE IinH -- -- -- -- IinL VOH VOL VIH VIL tpd 0.7 1.0 0.7 tset 2.0 3.5 2.0 0 thold 0 -0.5 0 2.2 fcount tr tf 250 0.5 0.5 -- -- -- -- -- 2.3 2.3 0 -0.5 0 2.2 250 0.5 0.5 -- -- -- -- -- 2.4 2.4 0 -0.5 0 2.2 250 0.5 0.5 -- -- -- -- -- 2.5 2.5 MHz ns ns -- -- -- -- 2.0 3.5 2.0 0 -- -- -- -- 2.0 3.5 2.0 0 -- -- -- -- ns 2.3 4.8 2.5 0.7 1.0 0.7 2.4 4.9 2.6 0.7 1.0 0.7 2.5 5.0 2.7 ns 0.5 -1.02 -1.95 -1.17 -1.95 430 670 535 380 -- -0.84 -1.63 -0.84 -1.48 -- -- -- -- 0.5 -0.98 -1.95 -1.13 -1.95 275 420 335 240 -- -0.81 -1.63 -0.81 -1.48 -- -- -- -- 0.3 -0.92 -1.95 -1.07 -1.95 275 420 335 240 -- -0.735 -1.60 -0.735 -1.45 A Vdc Vdc Vdc Vdc Min -- Max 165 Min -- 25 Max 150 Min -- 75 Max 165 Unit mA A
SEQUENTIAL TRUTH TABLE * S1 S2 D0 D1 D2 D3 Carry Clock Q0 Q1 Q2 Q3 Carry ** In Out L L L L L L H L H H H H L H H H H H H L L L L L L X X X X X X H X X X X L X X X X X X H X X X X H X X X X X X L X X X X H X X X X X X L X X X X X L L L H H X X L L L L H H H H L H H H H H H H L H L H H H H H L H L H L L H H H H H H H L L H H H H H H H H L L L L H H H H H H H H L L L L H L H H L H H H L H H L H
AC PARAMETERS
Propagation Delay Clock to Q Clock to Carry Out Carry in to Carry Out Set-up Time Data (D0 to C) Select (S to C) Carry In (Cin to C) (C to Cin) Hold Time Data (C to D0) Select (C to S) Carry In (C to Cin) (Cin to C) Counting Frequency Rise Time Fall Time ns
* Truth table shows logic states assuming inputs vary in sequence shown from top to bottom. ** A clock H is defined as a clock input transition from a low to a high logic level.
DIP PIN ASSIGNMENT
VCC1 Q2 Q3 COUT D3 D2 S2 VEE 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC2 Q1 Q0 CLOCK D0 D1 CIN S1
NOTE: Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through a 50-ohm resistor to -2.0 volts.
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6-11 of the Motorola MECL Data Book (DL122/D).
9/96
(c) Motorola, Inc. 1996
2-1
REV 6
MC10H136
LOGIC DIAGRAM
S1 9
S2 7 Carry In 10
Q0 T T Q0 C
T T
Q1 Q1 TC
T Q2 T T Q2 TC
T Q3 T T Q3 TTC
Clock 13
VCC1 = Pin 1 VCC2 = Pin 16 VEE = Pin 8
12 D0
14 Q0
11 D1
15 Q1
6 D2
2 Q2
5 D3
3 Q3
4 Carry Out
NOTE: FLIP-FLOPS WILL TOGGLE WHEN ALL T INPUTS ARE LOW.
APPLICATION INFORMATION
The MC10H136 is a high speed synchronous counter that operates at 250 MHz. Counter operating modes include count up, count down, pre-set and hold count. This device allows the designer to use one basic counter for many applications. The S1, S2, control lines determine the operating modes of the counter. In the pre-set mode, a clock pulse is necessary to load the counter with the information present on the data inputs (D0, D1, D2, and D3). Carry out goes low on the terminal count or when the counter is being pre-set.
MOTOROLA
2-2
MECL Data DL122 -- Rev 6
MC10H136
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C
B -N- Y BRK D -L- -M- W D Z
0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
20
1
X V VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
A Z R
0.007 (0.180) M T L-M 0.007 (0.180) M T L-M
S
N N
S
S
S
H
0.007 (0.180) M T L-M
S
N
S
C
E 0.004 (0.100) G G1 0.010 (0.250) S T L-M J -T-
SEATING PLANE
K1 K F VIEW S 0.007 (0.180)
M
VIEW S
S
T L-M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
MECL Data DL122 -- Rev 6
2-3
MOTOROLA
MC10H136
OUTLINE DIMENSIONS
L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE V
9
-A-
16
-B-
1 8
C
L
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. DIM A B C D E F G H K L M N INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01
-T-
SEATING PLANE
N E F D G
16 PL
K M J
16 PL
0.25 (0.010)
M
M
TB
S
0.25 (0.010)
TA
S
-A-
16 9
P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R
B
1 8
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01
F S
C
L
-T- H G D
16 PL
SEATING PLANE
K
J TA
M
M
0.25 (0.010)
M
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10H136/D*
MC10H136/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC10H136

	To Download MC10H136 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .